http://shop.ahinc.com For all your computing needs. service@flowtest.com en-us http://shop.hosemonster.com/product_info.php?products_id=18256 Item#=DDTANK1 Weight=6One-gallon mixing tank with manifold and fittings for the 2 1/2" Dechlor Demon offered as a replacement or additional. The DD2H includes this one-gallon tank. It can also be used as an additional tank when dechlorinating large amounts of water. With a second tank charged with fresh dechlorinating agent, the change-out of tanks results in minimal interruption of flow. 150.0000 http://shop.hosemonster.com/product_info.php?products_id=18257 Item#=DDTANK10 Weight=15Ten gallon tank with manifold and fittings for Dechlor Demon. This size tank us usually used with the 4" or 4 1/2" Dechlor demon. It can be ordered seperately for use on any size Dechlor Demon. It can also be used as an additional tank when dechlorinating large amounts of water. With a second tank charged with fresh dechlorinating agent, the change-out of tanks results in minimal interruption of flow. 205.0000 http://shop.hosemonster.com/product_info.php?products_id=17326 Item#=GK200 Weight=3Dial size: 2 ½" inch (63 mm) Connection: ¼" NPT Accuracy: 1 % Full Scale Range: 0 - 200 psi Filling: Glycerin Laminated Safety Glass Lens, Full Blow-Out Protection, Designed and manufactured to minimize failure and to protect personnel and property Included are: Brass Tee, Drain Valve, Brass Nipple, Quick Disconnect Male Plug and Female Coupler. All gauges tested at factory. Certification papers available at additional charge see part# GCC2H 93.0000 http://shop.hosemonster.com/product_info.php?products_id=17250 Item#=CASE520 Weight=6Gauge Case - Protect your gauges while not in use. The Gauge Case with pull-and-tear foam is configured by you to accommodate multiple gauges or other accessories. Outside Dimension Length 15.11" Width 12.40" Depth 6.94" Inside Dimension Length 13.61" Width 9.89" Depth 6.06" Included: Case Pinch and Tear Foam 92.0000 http://shop.hosemonster.com/product_info.php?products_id=17251 Item#=CASE720 Weight=10Protective Case - Protect your Gauges or Pitotless Nozzles while not in use. The Case has pull-and-tear foam to be configured by you to accommodate multiple Gauges or Pitotless Nozzles or other accessories. Outside Dimension Length 19.75" Width 15.53" Depth 7.48" Inside Dimension Length 18.29" Width 13.19" Depth 6.62" Included: Case Pinch and Tear Foam 163.0000 http://shop.hosemonster.com/product_info.php?products_id=10684 Item#=HM2HWCT Weight=30Factory Mutual Approved WCT - Western Canadian Fire Under The 2 1/2" Hose Monster with WCT threads is used for fire pump testing, rooftop standpipe testing, fire flow testing and flushing. It includes the built-in pitot system, flow chart and registratration form. Other accessories are usually required and will vary depending on the intended application. The Hose Monster is intended to be used with hose and should not be attached directly to a hydrant. 783.0000 http://shop.hosemonster.com/product_info.php?products_id=5019 Item#=HM2HIN Weight=10The 2 1/2" Mini-Monster In-Line unit is produced with a 4" groove on the outlet end to accommodate a 4" grooved coupling and fitting. It is used in special applications where the thrust neutralizing feature of the Hose Monster is not needed. The In-Line unit must be secured when flowing. It will not lie on the ground. Call us for more information. Underwriters Laboratories Certified and Factory Mutual Aproved for flow rate measurements. 783.0000 http://shop.hosemonster.com/product_info.php?products_id=9192 Item#=DDHOSE20 Weight=5These 3/4" x 20' extension hoses allow you to position the mixing tank away from the hydrant. We began offering this product in response to customers who use the Dechlor Demon on a hydrant, but leave the tank in the truck. Sold individually. Two are needed. Note: Photo is of 3/4" x 6' 99.0000 http://shop.hosemonster.com/product_info.php?products_id=5028 Item#=HM4HIN Weight=20The 4 1/2" Mini-Monster In-Line unit is produced with an 8" groove on the outlet end to accommodate an 8" grooved coupling and fitting. It is used in special applications where the thrust neutralizing feature of the Hose Monster is not needed. Underwriters Laboratories Certified and Factory Mutual Aproved for flow rate measurements. 799.0000 http://shop.hosemonster.com/product_info.php?products_id=5029 Item#=HM4INLINE Weight=20The 4" Mini-Monster In-Line unit is produced with an 8" groove on the outlet end to accommodate an 8" grooved coupling and fitting. It is used in special applications where the thrust neutralizing feature of the Hose Monster is not needed. It is the Underwriters Laboratories Certified and Factory Mutual Aproved for flow rate measurements. 799.0000 http://shop.hosemonster.com/product_info.php?products_id=343 Item#=HGV4NST Weight=15A hydrant gate valve used while flow testing or flushing means reduced stress on the hydrant and a greatly reduced chance of accidental water hammer. Also, if the hydrant happens to go bad during a flowing operation, just close the gate valve. Until now such a valve was impractical due to size and weight. This valve weighs only 15 pounds and measures 10 1/2" end to end. If flushing or flow testing WITHOUT the Dechlor Demon, attach this gate valve directly to the hydrant, then attach hose and Hose Monster. If flushing or flow testing WITH the Dechlor Demon, attach the DD to the hydrant and the gate valve to the DD. This option also enables the mixing tank of the Dechlor Demon to be filled with ease and control. 690.0000 http://shop.hosemonster.com/product_info.php?products_id=79 Item#=GCSW Weight=2Used for collecting static / residual pressures from a hydrant in a fire flow test. The Gauge Cap attaches to a 2 1/2" NST nozzle port on the test hydrant. It comes assembled as shown. The quarter-turn 1/4" ball valve is easy on the hands to operate. The swivel feature enables the user to position the gauge in a readable position. A guage is needed and is sold separately. 109.0000 http://shop.hosemonster.com/product_info.php?products_id=396 Item#=WSPA101 Weight=1Universal Spanner Wrench is used for tightening/loosening rocker lug and pin lug hose connections. Used with the HM2H, HM4 and HM4H. Made from tough, light AL-MAG 35 alloy, designed for hard usage. Weighs less than one pound. 16.0000 http://shop.hosemonster.com/product_info.php?products_id=74 Item#=GC Weight=2The solid Gauge Cap is used for collecting static / residual pressures from a hydrant in a fire flow test. The Gauge Cap attaches to a 2 1/2" NST nozzle port on the test hydrant. It comes assembled as shown. The quarter-turn 1/4" ball valve is easy on the hands to operate. The solid gauge cap costs less than the swivel gauge cap but when tightened on a hydrant nozzle, the gauge may be facing the wrong way. A Quick Disconnect Coupling (QDCOUP) is recommended to use on the gauge and the gauge port. A guage is needed and is sold separately. 71.0000 http://shop.hosemonster.com/product_info.php?products_id=2836 Item#=HGV25 Weight=4The Hydrant Slow Close Gate Valve is used for fire flow testing and main flushing to control the water flow from the hydrant. The use of this valve makes it easier to avoid water hammer and simplifies Hydrant Capacity Flow Tests. This valve connects directly to the 2 1/2" NST nozzle port on a hydrant and then to a hose. 284.0000 http://shop.hosemonster.com/product_info.php?products_id=342 Item#=HGV4.5NST Weight=15A hydrant gate valve used while flow testing or flushing means reduced stress on the hydrant and a greatly reduced chance of accidental water hammer. Also, if the hydrant happens to go bad during a flowing operation, just close the gate valve. Until now such a valve was impractical due to size and weight. This valve weighs only 15 pounds and measures 10 1/2" end to end. If flushing or flow testing WITHOUT the Dechlor Demon, attach this gate valve directly to the hydrant, then attach hose and Hose Monster. If flushing or flow testing WITH the Dechlor Demon, attach the DD to the hydrant and the gate valve to the DD. This option also enables the mixing tank of the Dechlor Demon to be filled with ease and control. 690.0000 http://shop.hosemonster.com/product_info.php?products_id=170 Item#=HW107 Weight=4The adjustable single head spanner wrench is used to remove hydrant caps, open and close hydrants and to attach/remove hose to/from hydrants and Hose Monsters. Included: Wrench 33.0000 http://shop.hosemonster.com/product_info.php?products_id=2818 Item#=H3.502H Weight=20Double jacket. 100% polyester yarn, rubber lined, 600 PSI Proof Test. This 3" x 50' coupled to 2 1/2' NST hardened aluminum rocker lug couplings. Hose is used with the Hose Monster for fire pump testing and for flowtesting / flushing from hydrants. Note: 2 1/2" x 10' white shown in photo Note #2: Yellow Note #3 Other lenghts are available special order. Please call for price and delivery. 246.5500 http://shop.hosemonster.com/product_info.php?products_id=2950 Item#=VDC6 Weight=2Vita-D-Chlor Tablets The safest and most environmentally conscious method of dechlorination. 6 tablets Active ingredient - Ascorbic Acid (vitamin C) 75% 85 gram (3 oz.) per tablet Inert ingredient - Water soluble organic binder 25% Diameter - 2-5/8" Thickness - 1" Weight each - 115g ( 4 oz) Appearance - White tablet with citrus odor One gram of Vita-D-Chlor (active ingredient) will neutralize 1 ppm (part per million) chlorine in 100 gallons of water. Other quantities available through us. 6 tablets 20 tablets 40 tablets More info at www.vita-d-chlor.com/Information.htm 50.0000 http://shop.hosemonster.com/product_info.php?products_id=2948 Item#=VDC20 Weight=6Vita-D-Chlor Tablets The safest and most environmentally conscious method of dechlorination. 20 tablets Active ingredient - Ascorbic Acid (vitamin C) 75% 85 gram (3 oz.) per tablet Inert ingredient - Water soluble organic binder 25% Diameter - 2-5/8" Thickness - 1" Weight each - 115g ( 4 oz) Appearance - White tablet with citrus odor One gram of Vita-D-Chlor (active ingredient) will neutralize 1 ppm (part per million) chlorine in 100 gallons of water. Other quantities available through us. 6 tablets 20 tablets 40 tablets More info at www.vita-d-chlor.com/Information.htm 165.0000 http://shop.hosemonster.com/product_info.php?products_id=2686 Item#=DDHOSE Weight=1Sold as individual Hose for replacement part. two are needed for the Dechlor Demon, all sizes. The Tube is 3/4" diameter x 6' in length. (other lengths are available and are not stocked, allow 3-4 weeks for delivery. Pricing varies depending on length of hose.) 79.0000 http://shop.hosemonster.com/product_info.php?products_id=2957 Item#=HM2HCSA Weight=30Factory Mutual Approved CSA - Canadian Standard Thread The 2 1/2" Hose Monster with CSA threads is used for fire pump testing, rooftop standpipe testing, fire flow testing and flushing. It includes the built-in pitot system, flow chart and registratration form. Other accessories are usually required and will vary depending on the intended application. The Hose Monster is intended to be used with hose and should not be attached directly to a hydrant. 783.0000 http://shop.hosemonster.com/product_info.php?products_id=2666 Item#=HM2HQST Weight=30Factory Mutual Approved QST - Province of Quebec Standard Thread The 2 1/2" Hose Monster with QST thread is used for fire pump testing, rooftop standpipe testing, fire flow testing and flushing. It includes the built-in pitot system, flow chart and registratration form. Other accessories are usually required and will vary depending on the intended application. The Hose Monster is intended to be used with hose and should NEVER be attached directly to a hydrant. 783.0000 http://shop.hosemonster.com/product_info.php?products_id=2896 Item#=HM2HAMA Weight=30Factory Mutual Approved AMA - Alberta Mutual Aid Thread The 2 1/2" Hose Monster with AMA threads is used for fire pump testing, rooftop standpipe testing, fire flow testing and flushing. It includes the built-in pitot system, flow chart and registratration form. Other accessories are usually required and will vary depending on the intended application. The Hose Monster is intended to be used with hose and should never be attached directly to a hydrant. 783.0000 http://shop.hosemonster.com/product_info.php?products_id=2665 Item#=HM2HBCT Weight=30Factory Mutual Approved BCT - British Columbia Threads The 2 1/2" Hose Monster with BCT threads is used for fire pump testing, rooftop standpipe testing, fire flow testing and flushing. It includes the built-in pitot system, flow chart and registratration form. Other accessories are usually required and will vary depending on the intended application. The Hose Monster is intended to be used with hose and should NEVER be attached directly to a hydrant. 783.0000